You can remove the snow blower from your Kubota tractor in about 30 minutes with basic tools. Learning how to remove snow blower from Kubota tractor is a key skill for seasonal changeovers and maintenance work.
Spring is coming and you need your loader back. That big snow blower is in the way now. You need to get it off safely without hurting yourself or the machine.
I’ve done this job many times on my own Kubota. It seems hard at first but gets easy with practice. You just need to follow the right steps in order.
This guide will walk you through the whole process. We’ll cover tools, safety, and each step you need to take. Let’s get that blower off and get you ready for spring work.
What You Need Before You Start
Gather your tools first. This makes the job go much smoother and faster. You don’t want to stop halfway to look for a wrench.
You’ll need basic hand tools. A socket set, wrenches, and a pry bar are key. Have a floor jack and some wood blocks ready too.
Get your tractor’s manual. The exact steps can change by model. My Kubota L series is a bit different from a BX model.
Wear good work gloves and boots. Parts can be heavy and sharp. Safety glasses are a smart idea as well.
Find a flat, hard spot to work. Concrete is best but packed dirt works. You need a stable surface for the jack and blower.
Clear space around the tractor. You’ll need room to move and set the blower down. A helper is great but you can do it alone.
Step-by-Step Removal Process
Start by lowering the blower to the ground. Make sure it sits flat and stable. This takes weight off the mounting points.
Shut off the tractor and set the parking brake. Take the key out too. You don’t want any accidental movement.
Disconnect the PTO shaft first. This is the spinning rod that gives it power. There’s usually a pin or clip to pull out.
Now tackle the mounting frame. Most Kubota blowers use two big pins on the sides. Drive these out with a punch and hammer.
Some models have top link brackets too. Check for bolts or pins up near the tractor’s rear. Remove anything that connects the blower to the tractor.
Once all links are free, slowly back the tractor away. Go inch by inch and watch the blower. It should stay put on the ground as you move.
Knowing how to remove snow blower from Kubota tractor means doing these steps in order. Skipping ahead can cause damage or make things stuck.
Dealing with the Drive System
The PTO shaft needs care. It’s easy to bend or damage during removal. Always support it as you disconnect.
Many Kubota setups use a quick-attach coupler. You pull a ring back to release it. Others might have a simple pin connection.
If the shaft feels stuck, don’t force it. A little spray lubricant can help. Let it soak for a minute then try again.
Once free, set the shaft aside safely. Don’t let it drag on the ground. Hang it up or lay it straight to keep it good.
Check the tractor’s PTO stub too. Make sure it’s clean and has no damage. You’ll connect other tools here later.
This is a key part of learning how to remove snow blower from Kubota tractor. The drive system is the heart of the attachment.
Take your time here. Rushing can lead to costly repairs later. A bent PTO shaft is no fun to fix.
Handling the Mounting Frame
The frame holds all the weight. It’s usually the heaviest part of the whole assembly. This is where your jack comes in handy.
Look for the main lift arms. These connect to your tractor’s three-point hitch. There should be pins or balls on each side.
Remove the lower pins first. These often have hairpin clips or linch pins. Pull the clip, then drive the pin out.
Now do the top link. This might be a threaded turnbuckle or a pin. Loosen any nuts before trying to remove it.
Some frames have extra stabilizer bars. These keep the blower from swaying side to side. Check your manual for their location.
As you remove each part, set it aside neatly. Keep pins with their clips. This makes reassembly much easier next winter.
When you learn how to remove snow blower from Kubota tractor, the frame is your main focus. Get this right and the rest is simple.
Using a Jack for Support
Never let the blower fall free. It’s heavy and can hurt you or break things. A good floor jack is your best friend here.
Place the jack under the blower’s main frame. Use a wood block between the jack and metal. This stops slipping and protects the finish.
Lift just enough to take the weight. You don’t need to pick the whole blower up. Just support it so it’s not hanging on the tractor.
As you back the tractor away, lower the jack slowly. Keep the blower upright and steady. Go little by little.
Once the tractor is clear, lower the blower all the way. Set it on blocks if your floor is uneven. This keeps it stable for storage.
According to OSHA, proper support of heavy equipment prevents most workshop injuries. Don’t skip this safety step.
Part of knowing how to remove snow blower from Kubota tractor is working safe. The jack makes a hard job much easier.
Storage Tips After Removal
Clean the blower well before storing it. Hose off any salt and dirt. Let it dry completely to stop rust.
Check the auger and chute for damage. Now is a good time to fix any bent paddles or worn parts. You’ll forget by next winter.
Grease all the zerks you can find. The auger shaft and chute pivot need fresh grease. This keeps things moving freely next season.
Spray a light oil on any bare metal spots. The scraper bar and skid shoes can rust. A little protection goes a long way.
Store it in a dry place if you can. A shed or garage is best. Cover it with a tarp to keep dust off.
Keep all the pins and clips together. Put them in a bag and tape it to the blower. You’ll thank yourself next November.
Proper storage is the last step in how to remove snow blower from Kubota tractor. Do it right and it will last for years.
Common Problems and Fixes
Stuck pins are a normal issue. They get rusty and won’t budge. Don’t just hit them harder with a bigger hammer.
Use penetrating oil first. Spray it on and wait ten minutes. Tap the pin gently to help the oil soak in.
A pin punch helps direct your hits. Place it on the pin end and strike that. This focuses the force where you need it.
Sometimes the blower won’t separate from the tractor. It might be hanging up on the PTO shaft. Check alignment before forcing anything.
The ANSI sets standards for equipment connections. Kubota follows these for safe attachment designs.
If things feel really stuck, stop and look. There might be a hidden bolt or clip you missed. Go back to your manual.
Learning how to remove snow blower from Kubota tractor includes solving these hiccups. Every removal teaches you something new.
When to Ask for Help
Some jobs are too much for one person. If the blower is very large or heavy, get a helper. Safety always comes first.
Newer Kubota models might have hydraulic connections. These need special care to avoid leaks. Don’t guess if you’re not sure.
If a pin is badly bent or broken, you might need parts. Order them before forcing things. A broken casting costs a lot.
Your local Kubota dealer can help. They’ve seen every problem before. Sometimes a quick phone call saves hours of struggle.
The John Deere website has good general tractor maintenance guides too. Many principles are the same across brands.
There’s no shame in asking. I still call my dealer with questions sometimes. It’s better than breaking something expensive.
Knowing how to remove snow blower from Kubota tractor also means knowing your limits. Work smart, not just hard.
Getting Ready for Spring Attachments
With the blower off, you have a clean tractor. Now is the perfect time for some quick maintenance.
Check the three-point hitch arms. Grease them well since they were covered all winter. Look for any wear or play.
Inspect the PTO shield and cover. Make sure it moves freely and isn’t cracked. This safety part is important.
Now you can mount your mower or tiller. The process is similar but in reverse. You’ll be an expert at attachments soon.
According to Agriculture.com, regular attachment changes extend tractor life. It keeps all systems working smoothly.
Take a moment to admire your work. You saved dealer fees and learned a new skill. That feels pretty good.
Mastering how to remove snow blower from Kubota tractor opens up other projects. You’ll feel more confident with all your implements.
Frequently Asked Questions
How long does it take to remove a Kubota snow blower?
About 30 minutes once you know the steps. Your first time might take an hour. Go slow and follow the manual.
Can I remove it without a floor jack?
It’s possible but not safe. The blower is very heavy. A good jack supports the weight and prevents drops.
Do I need special tools to remove the snow blower?
Basic mechanic’s tools are enough. Sockets, wrenches, a hammer, and punch will do it. Your tractor might come with some tools too.
How do I remove snow blower from Kubota tractor if the pins are frozen?
Use penetrating oil and heat if needed. A propane torch can help expand the metal. Be careful around fuel and hoses.
Should I disconnect the battery first?
It’s a good safety habit. You won’t be near electrical systems much, but it never hurts. Better safe than sorry.
How do I store the PTO shaft properly?
Keep it clean and straight. Hang it on a wall or lay it flat. Don’t let it kink or get run over.
Conclusion
So that’s how to remove snow blower from Kubota tractor. It’s a straightforward job with the right approach.
Take your time, use proper support, and follow your manual. Each model has small differences in the process.
You’ll get faster each season you do it. Soon it will feel like a simple routine task. Enjoy your tractor in its spring configuration.
